When something stops working and you can not immediately tell why, that is the call to make. A dead outlet, a breaker that will not stay reset, lights that dim every time the dishwasher runs, a switch that sparks when you flip it. These are not problems to watch and wait on. They are the kind of faults that get worse when they are left alone, and diagnosing them is exactly the work we do across Keller and the surrounding area.
We cover residential and commercial electrical work throughout Keller, from straightforward repairs to full panel upgrades and new circuit runs. We scope every job on the call and confirm the price before anything is scheduled.
Call (469) 249-3264 and tell us what is happening.
We will tell you what it likely involves and what it will cost to fix.
We are available every day from 6:30 AM to 8:30 PM, which covers early starts and evening appointments. That matters for homeowners who cannot take time off mid-week and for businesses that need electrical work handled before or after operating hours. When you call, we scope the job on the phone, confirm the price, and find a time that works. Nothing is booked without a price agreed first.
If the problem will not keep, say so when you call. Emergency faults are answered, and we work through what the schedule allows for short-notice requests. The call is where that conversation happens.
A fault in a rental unit has a timeline attached to it that a homeowner's does not. We work with property managers and landlords who need access coordinated around tenants, and with businesses that need electrical work handled without shutting operations down for the day. Tell us the situation on the call and we will work through the access and timing before the visit is confirmed.
Keller's housing stock includes a range of ages and build types, and what is inside the walls varies accordingly. Older homes may have aluminum branch circuit wiring, ungrounded outlets, or panels that have not been touched since the house was built. Matching a new device or circuit to what is already in the property is not always as simple as pulling a replacement off the shelf.
Where aluminum wiring is present, remediation at the connection points is often the right scope rather than a full rewire. The connections are where the risk lives, and treating them correctly means using the right materials and methods for the existing wiring rather than improvising with standard copper fittings. We assess what is there before quoting the work.
When a part or fitting is genuinely obsolete, we say so on the call. If something has to be sourced before the work can be completed, that gets explained before the visit is confirmed, not after the job has already started. The work area is left as it was found when we are done, whether the job takes an hour or a full day.
The price for any job is confirmed on the call, based on what you describe. What the fault turns out to be, what has to be opened up to reach it, and whether the existing circuit or panel can carry the change are the things that move a quote. We ask the right questions up front so the number we give you reflects the actual job rather than a best guess.
Adding a circuit is often simpler than people expect. A dedicated run from the panel to a new outlet or appliance connection is a straightforward scope in most cases, and the call is where we confirm whether your panel has the capacity to support it without any additional work.
If something unexpected turns up on site, that conversation happens before the additional work proceeds. You are told what the new scope involves and what it costs before anything changes. Nothing is added after the fact without agreement. Ask what the quote covers and you get a straight answer. To see how it all fits together, read our list of electrical services.
When a job is finished, we test every circuit and device that was worked on before we leave. Outlets are checked for correct wiring and ground continuity. Breakers are cycled. Fixtures and fans are run through their functions. Panel work is confirmed before the cover goes back on.
Where new circuits or devices are added, labeling is part of the job. A panel that is correctly labeled tells the next electrician, the next owner, and the building inspector exactly what is on each breaker. That matters when the property is sold, when a tenant moves out, or when a permit inspection needs to be passed.
We write down what was done and leave a clear record of the work. For an older property where the wiring history is unclear, that documentation is worth having. Electrical work done to the code inspectors here enforce is what gets the permit closed and the property ready for whatever comes next.
A dead outlet is not always a failed device. It may be a tripped GFCI upstream, a loose connection at the back of the outlet, or a breaker that has partially failed. We trace the fault before replacing anything. Where an outlet needs replacing, we confirm the right type for the location. GFCI protection is required in kitchens, bathrooms, garages, and outdoor locations. AFCI protection is required in bedrooms and living areas in most residential builds and renovations. Older homes in this area frequently lack both, and a pre-sale inspection or remodel will surface the gaps.
A power strip with a surge suppressor protects what is plugged into it and nothing else. Severe thunderstorms and the occasional grid event in this region can send voltage spikes through the utility line that reach every circuit in the house simultaneously. A whole-panel surge protector installs at the service panel and catches that energy before it reaches the wiring and connected devices. It is a single installation that covers the whole house from that point forward.
Outdoor outlets need materials and methods rated for exterior exposure: weatherproof covers, GFCI protection, and conduit where the wiring runs are exposed. A backyard outlet that was installed without the right enclosure is a fault waiting to show up. We install outdoor outlets correctly from the start and replace ones that were not.
Recessed lighting layout involves more than cutting holes in a ceiling. The circuit has to support the load, the boxes have to be rated for the insulation contact situation in the ceiling, and the placement has to work with the room's function rather than just its dimensions. LED retrofits are often a straightforward swap, but older fixtures with incompatible dimmers or wiring that was not run for the load can complicate the job. We confirm the scope on the call.
Each of these appliances requires a dedicated 240-volt circuit, sized for the load it will carry. Sharing a circuit with other loads is a code violation and a practical problem. When a range or dryer trips a breaker repeatedly, a dedicated circuit is usually the fix. We run the circuit from the panel, confirm the breaker sizing, and install the correct outlet for the application. If the panel is near capacity, that conversation happens before the circuit is run.
An inspection covers panel condition, grounding and bonding, wiring type and age, GFCI and AFCI coverage, and outlet and switch condition throughout the property. Arc-fault and ground-fault protection, service-entrance condition, and the state of any aluminum branch circuit wiring are all part of what gets assessed. The result is a clear picture of where the system stands against current code. People call for inspections before buying a home, before listing one, or to satisfy rental compliance requirements. We explain what each finding means and what addressing it involves. Nothing is scheduled without a price confirmed first.
We serve Keller and the surrounding communities throughout Tarrant County. That includes Westlake, Watauga, Southlake, North Richland Hills, and Trophy Club.
If you are in the area and want to confirm your address falls within our range, call (469) 249-3264 and we will check.
Coverage is the same across all of these areas. The same work, the same process, the same availability every day from 6:30 AM to 8:30 PM. Commercial and residential calls are both handled. Call to confirm and get a quote.
Rough-in is the wiring work done before walls are closed: running cables, installing boxes, and getting the conductors to where they need to be. Trim-out is the finish work done after the walls are complete: installing outlets, switches, fixtures, and covers, and connecting the devices to the wiring already in place.
In most cases, yes. Work on a single circuit or outlet can usually be scoped to minimize disruption, and we talk through the access situation on the call before the visit is confirmed. If the job requires the service to be shut off, we work out a time that fits the business's schedule rather than assuming a mid-day window works.
Yes, and in specific ways. Homes built several decades ago may have aluminum branch circuit wiring, ungrounded outlets, panels that lack space for modern circuit loads, or GFCI and AFCI protection that was never installed because it was not required at the time. None of these are automatic emergencies, but they are worth knowing about before a renovation, a sale, or a new appliance is added. We assess what is there and explain what, if anything, needs attention.
Call (469) 249-3264 and reference the previous job.
We confirm the scope of the follow-up, the price if additional work is involved, and the available schedule before booking the return visit. Follow-up visits are handled the same way as the original job: scope and price confirmed on the call before anything is scheduled.
The report covers panel condition, wiring type and age, grounding and bonding, GFCI and AFCI protection, and outlet and switch condition throughout the property. It is useful for buyers who want to know what they are taking on, sellers who want to get ahead of what an inspection will find, and landlords who need to confirm the property meets current requirements. We walk through what the findings mean in plain terms, not in code citations.
We trace the fault. We fix the wiring. We restore the power. Every job is tested before we leave, the work area is left as it was found, and you get a straight account of what was done.
Call (469) 249-3264 any day between 6:30 AM and 8:30 PM.
Tell us what is happening, and we will tell you what it takes to fix it.
Also serving: Watauga, Southlake, North Richland Hills, Colleyville, Hurst.
Below is a plain-language look at the electrical work we handle for homes and commercial properties in Keller and across Tarrant County. Each row covers what the service includes, who it fits best, and one practical thing worth knowing before you call.
If a row describes a problem you recognize, call us at (469) 249-3264 and we will walk through what the job involves and confirm a price before anything is scheduled.
| Type of Work | What the Job Involves | Ideal For | Things to Know |
|---|---|---|---|
| Dedicated Appliance Circuits | Dryer and range circuitsRefrigerator and dishwasher circuitsHot tub and pool supply wiring240-volt circuit installation | Homeowners installing a large appliance or dealing with a breaker that trips under appliance load | Sharing a circuit with other loads is a code violation for most major appliances. A dedicated circuit is the correct fix and usually the permanent one. |
| Electrical Panel & Service Upgrades | 100-to-200-amp service upgradeLoad calculationsPanel replacementCapacity checks before new circuits | Older homes adding appliances, EV chargers, or square footage | Tarrant County summers put sustained load on panels for months. Older 100-amp services in Keller neighborhoods frequently can not keep up with modern household demand. |
| Wiring & Circuit Installation | New circuit runs from the panelCircuit sizing for the loadWiring for additions and outbuildingsSubpanel installation where needed | Remodels, additions, garages, and workshops that need circuits from scratch | Adding a circuit is often simpler than people expect. Panel capacity is confirmed before any wiring starts mid-job. |
Call (469) 249-3264 any day between 6:30 AM and 8:30 PM and we will walk through what the job involves, confirm a price, and get it on the schedule.
(469) 249-3264